If your powermatic 2000 table saw motor is on its last legs, it may be time to replace it. Here’s how to remove the old motor, configure the new one, and install a new one. The following steps will help you perform the process correctly. Keep reading to learn more! After you’ve removed the old motor, you should replace the mounting plate, motor, and pulley. You can replace the belt and pulley on the same saw, but be sure to replace the whole assembly.
Powermatic 2000 table saw motor configuration
The Powermatic 2000 table saw uses a patented motor configuration to maximize cutting performance and provide years of trouble-free use. It features a large stance for easier blade raising and tilting, and a heavy-duty box trunnion that prevents slipping. This saw also comes with a poly-V drive belt system for quieter power transfer and less vibration, which means a lower chance of heat buildup. It also features an improved built-in dust collection port for convenient access to the saw cabinet. Safety features include a proprietary safety switch with magnetic interlock. It has an on/off switch and a knee-activated stop button.
The Powermatic 2000 table saw motor configuration varies depending on the saw model. The PM2000 table saw has a three-phase motor configuration, and it can be converted from a three-phase to a single-phase motor. It comes with a dust shroud and a 4″ dust collector hose. Among the other features, this table saw includes a dust collection system that minimizes ejection of dust from the blade, ensuring that the entire cabinet is clean. It also features a 4″ dust collection hose and a push-button arbor lock. It is also equipped with an Accu-Fence, which improves accuracy and safety.
The Powermatic PM2000 has a magnetic on/off switch that can be accessed by either a ring or a switch. The green pilot light shows that the saw is connected to electrical power. The start button is illuminated, and the OFF switch can be turned off when you’re not around to prevent accidental start-up. The Powermatic PM2000 is available with a three-horsepower single-phase motor or five-horsepower three-phase motor. The motors are of high quality and are rated for actual developed power.
Powermatic 2000 table saw power conversion
When you are upgrading your table saw, you should consider the power conversion that is available. Single phase power will work, and you can purchase a new two line wire from your local hardware store to make the switch. Single phase power will require the black and white leads. If you need to use 3 phase power, you will need to buy new 3 line wire. It will be easier to install this type of table saw if you know a little about electrical wiring.
A table saw with 1.5 to 2 HP motor will only require a 120-volt circuit, while one with three to five horsepower will require a 240-volt outlet. You may need to purchase a new motor for a saw with a higher horsepower. This type of table saw will cut wood up to 2 inches thick. It is recommended to purchase a table saw with a 5HP or higher motor if you intend to cut thicker wood.
When you choose a table saw, make sure you purchase one with a safety mechanism, especially a blade guard. Jet and Powermatic table saws both have built-in safety devices such as a riving knife, and all have an electric fuse to prevent kickback. These devices stop the blade in an instant if they come into contact with conductive objects, such as wet wood or metal. However, the two-piece guard and antikickback pawls are difficult to adjust and cannot be calibrated.
How to remove old motor from powermatic 2000 table saw
Before you can replace the motor in your Powermatic 2000 table saw, you should understand the wiring. Single phase power uses black and white leads, while three-phase power requires an extra red wire. The new motor has a pulley that must fit at the same distance from the mounting plate. You can buy a new 2-line wire at your local hardware store. Afterward, you can replace the old motor with the new one.
A capacitor sits underneath the plastic or metal housing of the saw. This component is connected to the starter switch. When this component fails, the saw will not start. Fortunately, this part is cheap and easy to replace. A failed capacitor will typically have bulged or split wires. If it isn’t, you should try removing it and replacing it. This will help you to avoid further damage.
